American Standard 4508.801.002 Instalační příručka

Procházejte online nebo si stáhněte Instalační příručka pro Zdravotnický sortiment American Standard 4508.801.002. American Standard 4508.801.002 Installation Guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 6
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
M968832 Rev.1.4
4508.801
Certified to comply with ANSI A112.18.1
Installation
Instructions
1
2
1
3
4
6
12
5
SLOT
Insert SPOUT (1) and CABLE CONNECTOR (12) through center hole, making sure
the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto
SPOUT SHANK (7) from under side of sink . Make sure SPOUT (1) is centered
in the mounting hole and the slot in the BRASS WASHER (5) faces toward the
rear of the sink.
Tighten LOCKNUT (6) firmly. Fig. A.
1
1A
INSTALL SPOUT
INSTALL VALVE BODY
1
10
9
8
11
7
Adjustable Wrench Screwdriver Channel Locks
Recommended tools
Tubing Cutter
Fig. A.
MOUNTING
SURFACE
Hand tighten LOCKNUT (11) to secure VALVE BODY (8).
Repeat above steps for opposite VALVE BODY (8A).
Install LOCKNUT (11) onto VALVE BODY (8).
From under side of mounting surface, install VALVE BODY (8) through valve
mounting holes. Threads of VALVE BODY (8) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread ESCUTCHEON (10)
onto VALVE BODY (8) until snug against internal stop. If necessary, adjust
LOCKNUT (11).
10
9
8
11
Place RUBBER RING (9) into SCUTCHEON (10).
5/16'' MIN.
8A
Fig. B.
PRINCETON
Spread Lavatory Faucet with
Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the rst time, every time.
Turn off water at
main supply.
CAUTION
Zobrazit stránku 0
1 2 3 4 5 6

Shrnutí obsahu

Strany 1 - PRINCETON

M968832 Rev.1.44508.801Certified to comply with ANSI A112.18.1InstallationInstructions121346125SLOTInsert SPOUT (1) and CABLE CONNECTOR (12) through ce

Strany 2 - REAR OF SINK

M968832 Rev.1.46POP-UP KNOB (1) must be fully down. Fig. B. FLANGE GASKET AND POP-UP KNOBWHITE FOAMGASKETNOT VISIBLEDRAINFLANGEFig. A.Fig. B.Check DR

Strany 3 - CHECK OPERATION OF POP-UP

M968832 Rev.1.4Connect HOT water supply to inlet of left SHANK and COLDwater supply to right SHANK using sealant, appropriateconnectors, and COUPLING

Strany 4 - M968832 Rev.1.4

M968832 Rev.1.4CHECK DRAIN CONNECTIONS11121314TEST INSTALLED FITTINGWith HANDLES (1) in OFF position, turn on WATERSUPPLIES (2) and check all connecti

Strany 5 - Speed Connect™ Drain

M968832 Rev.1.4Speed Connect™ DrainTroubleshooting GuideDisconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fi

Strany 6

M968832 Rev.1.4STOPPER INSTALLATION PROCEDURELocked Mode: Look at the Plastic Loop at the bottom of the Stopper and noticethat the Loop is on one side

Komentáře k této Příručce

Žádné komentáře