American Standard 7010.801.002 Instalační příručka

Procházejte online nebo si stáhněte Instalační příručka pro Zdravotnický sortiment American Standard 7010.801.002. American Standard 7010.801.002 Installation Guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 7
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
M968598 Rev.1.4
6
5
MOUNTING
SURFACE
SPOUT BASE
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT (1), CABLE CONNECTOR (2) and SPOUT HOSE (3) through center hole,
making sure the SEAL WASHER (4) is properly seated in spout base.
Assemble RUBBER WASHER (5), LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the
mounting hole.
Tighten LOCKNUT (6) firmly. Fig. A.
Tighten LOCKNUT (9) with WRENCH (12) (supplied) to secure VALVE
BODY (11). Repeat above steps for opposite VALVE BODY (11a).
Install LOCKNUT (9) and RUBBER WASHER (10) onto VALVE BODY (11).
From under side of mounting surface, install VALVE BODY (11) through valve
mounting hole. Threads of VALVE BODY (11) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread DECK ADAPTER (8)
onto VALVE BODY (11) until snug against internal stop. If necessary,
adjust LOCKNUT (9). Align as shown.
1
1A
7010.801
Certified to comply with ANSI A112.18.1
Installation
Instructions
GREEN TEA
Spread Lavatory Faucet with
INSTALL SPOUT
INSTALL VALVE BODIES
4
3
12
8
7
10
9
11
11a
8
7
10
9
Place RUBBER RING (7) into DECK ADAPTER (8).
11
5/16'' MIN.
7
Speed Connect™ Drain
Adjustable Wrench Screwdriver Channel Locks
Recommended tools
Tubing Cutter
Fig. A.
Fig. B.
1
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the rst time, every time.
1
2
Zobrazit stránku 0
1 2 3 4 5 6 7

Shrnutí obsahu

Strany 1 - Instructions

M968598 Rev.1.465MOUNTINGSURFACESPOUT BASETurn off hot and cold watersupplies before beginning.CAUTIONInsert SPOUT (1), CABLE CONNECTOR (2) and SPOUT

Strany 2 - REAR OF SINK

M968598 Rev.1.42 6POP-UP KNOB (1) must be fully down. Fig. B. FLANGE GASKET AND POP-UP KNOBFig. A.Check DRAIN FLANGE in SINK to ensure thatWHITE FOAM

Strany 3 - ATTACH CABLE CONNECTOR

M968598 Rev.1.4 9WATER SUPPLY, TEE, SPOUT AND WASTE CONNECTIONSNOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDEDAND MUST BE PURCHASED SEPARA

Strany 4 - M968598 Rev.1.4

M968598 Rev.1.410INSTALL HANDLESCHECK DRAIN CONNECTIONS111214TEST INSTALLED FITTINGSERVICE290˚ If spout drips, operate handles several times fromOFF t

Strany 5 - Speed Connect™ Drain

M968598 Rev.1.4Fig. F.5Speed Connect™ DrainTroubleshooting GuideDisconnect the Cable from the Drain by threading the Cable Connector (1) counter-clock

Strany 6

M968598 Rev.1.4LOOP TOWARDREAR OF SINKFig. G.LOGOSTOPPER INSTALLATION PROCEDURELocked Mode: Look at the Plastic Loop at the bottom of the Stopper and

Strany 7

M968598 Rev.1.47Spread Lavatory Faucetwith Speed Connect™ Drain M961634-0070AVALVE MTG. KIT994053-0070ACARTRIDGEM962619-0070ADECK ADAPTER KIT024220-0

Komentáře k této Příručce

Žádné komentáře