American Standard 2555.801.295 Instalační příručka

Procházejte online nebo si stáhněte Instalační příručka pro Zdravotnický sortiment American Standard 2555.801.295. American Standard 2555.801.295 Installation Guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 7
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
4
6
14
5
SLOT
MOUNTING
SURFACE
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT (1) and CABLE CONNECTOR (14) through center hole, making sure
SEAL WASHER (2) is properly seated in SPOUT BASE (3).
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.
Tighten LOCKNUT (6) firmly. Fig. A.
Tighten LOCKNUT (11) with WRENCH (8) (supplied) to secure VALVE
BODY (13). Repeat above steps for opposite VALVE BODY (13A).
Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).
From under side of mounting surface, install VALVE BODY (13) through valve
mounting holes. Threads of VALVE BODY (13) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread DECK ADAPTER (10)
onto VALVE BODY (13) until snug against internal stop. If necessary, adjust
LOCKNUT (11).
1
1A
Certified to comply with ANSI A112.18.1
Installation
Instructions
Spread Lavatory Faucet
with Speed Connect™ Drain
INSTALL SPOUT
INSTALL VALVE BODY
1
2
1
8
10
9
12
11
13
13a
10
9
12
11
3
Place RUBBER RING (9) into DECK ADAPTER (10).
13
5/16'' MIN.
7
Adjustable Wrench Screwdriver Channel Locks
Recommended tools
Tubing Cutter
Fig. A.
Fig. B.
1
M968787 Rev. 1.5
2555.801
TOWNSQUARE
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the rst time, every time.
Zobrazit stránku 0
1 2 3 4 5 6 7

Shrnutí obsahu

Strany 1 - TOWNSQUARE

46145SLOTMOUNTINGSURFACETurn off hot and cold watersupplies before beginning.CAUTIONInsert SPOUT (1) and CABLE CONNECTOR (14) through center hole, mak

Strany 2 - Fig. A. Fig. B

M968787 Rev. 1.5Thread FLANGE (1) counter-clockwise and removeFLANGE (1) and FOAM GASKET (2) from drainbody. Fig. A.Thread LOCKNUT (3) clock-wise to b

Strany 3 - CHECK OPERATION OF POP-UP

Connect HOT water supply to inlet of left SHANK and COLDwater supply to right SHANK using sealant, appropriateconnectors, and COUPLING NUTS.Connect 1-

Strany 4 - M968787 Rev. 1.5

M968787 Rev. 1.5CHECK DRAIN CONNECTIONS111012TEST INSTALLED FITTINGWith HANDLES (1) in OFF position, turn on WATER SUPPLIES (2)and check all connectio

Strany 5 - Speed Connect™ Drain

Speed Connect™ DrainTroubleshooting GuideDisconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.Look at th

Strany 6

STOPPER INSTALLATION PROCEDURELocked Mode: Look at the Plastic Loop at the bottom of the Stopper and noticethat the Loop is on one side of the Stopper

Strany 7

072574-0070AEXTENSION ROD066116-YYY0ADRAIN STOPPERM961711-0070ATAILPIECE INSERT070847-0070ACLIP066118-0070APIVOT ROD KITM953450-YYY0ACOMPLETEDRAIN ASS

Komentáře k této Příručce

Žádné komentáře