American Standard Chandler Americast 7182.000 Uživatelský manuál stáhnout pdf

CHANDLER™ AMERICAST™ ISLAND SINK

WITH FAUCET HOLES 7182.001/7182.803

WITHOUT FAUCET HOLES 7182.000

ISLAND SINK MODEL 7182.001/803

ISLAND SINK MODEL 7182.000

Installation

Instructions

791267-400 Rev. C

Thank you for selecting American-Standard...the benchmark

of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

BEFORE YOU BEGIN...Unpack new sink and

inspect carefully for damage. Replace the sink

in its original packing carton to protect it until

you are ready to begin installation.

™

CUTOUT DIMENSIONS FOR SINK

Recommended Tools & Materials

Silicone Sealant

Putty Knife

Pipe Wrench

Channel Locks

Phillips Screwdriver

Regular Screwdriver

Adjustable Wrench

Drill

Locate and mark center lines of sink on countertop.

Provide proper clearance under the countertop for

the faucet supply lines and the structural parts of the

cabinet.

Cut out correct template and trace the cut line onto

the countertop at the proper location.

NOTE: If replacing an existing sink be certain to shut

off water supplies before removing old sink.

Mineral Spirits

Basin Wrench

Saber Saw

Tubing Cutter

Tape Measure

Hacksaw

Scissors

Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.

6-23/32"

(171mm)

6-23/32"

(171mm)

14" (356mm)

14-1/2" Radius

(368mm)

14-1/2" Radius

(368mm)

15" (381mm)

3/4" (19mm)

CENTER LINE

SINK

OUTLINE

SINK

OUTLINE

1/2"TYP.

CUTTING

LINE

CUTTING

LINE

CUTOUT FOR NEW INSTALLATION

MODIFICATION REQUIRED TO FIT ISLAND SINK

WITH FAUCET HOLES INTO A STANDARD

15" X 15" SINK CUTOUT

NOTE: CHANDLER ISLAND SINK WITHOUT

FAUCET HOLES DOES NOT FIT INTO A

STANDARD 15" X 15" SINK CUT OUT

8-11/32"

(212mm)

14"

(356mm)

15 "

(381mm)

16-1/2" (419mm)

14" (356mm)

SINK

OUTLINE

CUTTING

LINE

Certified to comply with ANSI A112.19.4.M

U.S. Patent No. 4,664,982

Other patents pending.

CAN/C.S.A. B-45

Observe local plumbing and building codes.

6-23/32"

(171mm)

6-23/32"

(171mm)

7-25/32"

(198mm)

11-9/32"

(287mm)

5-21/32"

(144mm)

12-3/8"

(314mm)

14-1/2" Radius

(368mm)

14-1/2" Radius

(368mm)

15-9/16"(395mm)

16-1/2" (419mm)

CENTER LINE

OF BOWL

1 2 3 4 5 6 7

Shrnutí obsahu

Strany 1 - Instructions

CHANDLER™ AMERICAST™ ISLAND SINKWITH FAUCET HOLES 7182.001/7182.803WITHOUT FAUCET HOLES 7182.000ISLAND SINK MODEL 7182.001/803ISLAND SINK MODEL 7182.0

Strany 2 - AFTER THE CUTOUT IS DRAWN

AMERICAST® LIMITED LIFETIME WARRANTYIf an American-Standard Americast® brand product is found to be defective in materials or workmanship, after insp

Strany 3

UNDERCOUNTER MOUNTING FOR CHANDLER,LAKELAND, PALISADE AND SILHOUETTE™ KITCHEN SINKSMODELS 7145, 7162, 7163 STANDARD, 7103, 7172, 7173, 7179, 7182, 718

Strany 4 - SUPPORT CLIP LOCATIONS:

965mm(38)MODEL 7196559mm(22)838mm(33)559mm(22)MODEL 7145, 7163 STANDARD,7179559mm(22)MODEL 7172457mm(18)MODEL 7185IMPORTANT: DIMENSIONS OF FIXTURES AR

Strany 5

ABSingle Bowl Double BowlTrapTrap12Drill a clearance hole inside the cutout line. Connect supply lines tofaucet finger tight, andcarefully bend to eng

Strany 6

790088-100 REV. HRefer to American Standard roughing-in information for specific dimensions for each model.Below are the dimensions of each sink. Make

Strany 7 - CARE AND CLEANING

©AMERICAN STANDARD INC. 2003 AMERICAST® LIMITED LIFETIME WARRANTYIf an American-Standard Americast® brand product is found to be defective in mat