American Standard Compact Cadet 3 2568 Uživatelský manuál stáhnout pdf

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

SAVE FOR FUTURE USE

CLOSET FLANGE

CLOSET BOLTS

7301270-100 Rev. A

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

COMPACT CADET

3 - 1.6 GPF ONE-PIECE TOILET

COMPACT CADET

3 FloWise™ - 1.28 GPF ONE-PIECE TOILET

ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet flange centerline must be as listed below:

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and

install wax ring evenly around waste flange (horn), with

tapered end of ring facing toilet. Apply a thin bead of

sealant around toilet base.

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange so bolts project

through mounting holes.

b. Loosely install retainer washers and nuts. Side of washers marked "THIS

SIDE UP" must face up!

WAX RING

SEALANT

WASHER

NUT

FLANGE

BOLT

Model 2568 – Compact Elongated Right Height™ with Seat

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure

your installation conforms to local codes.

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90

, and slide

into place 6" (152 mm) apart and parallel to wall.

724mm

(28-1/2)

159mm

(6-1/4)

16 ± 6mm

(5/8 ± 1/4)

419mm

(16-1/2)

292mm

(11-1/2)

267mm

(10-1/2)

724mm

(28-1/2)

381mm

(15)

394mm

(15-1/2)

79mm

(3-1/8)

FINISHED WALL

422mm

(16-5/8)

305mm

(12)

C/L OF OUTLET

241mm

(9-1/2)

140mm

(5-1/2)

SUPPLY

REQ'D

FINISHED

FLOOR

C/L OF SEAT POST

HOLES 140mm

(5-1/2) CENTERS

INSTALLATION INSTRUCTIONS

1 2 3 4

Shrnutí obsahu

Strany 1 - INSTALLATION INSTRUCTIONS

RECOMMENDED TOOLS AND MATERIALSPutty Knife Regular Screwdriver Adjustable Wrench Sealant Tape MeasureHacksaw Wax Ring/Gasket Flex

Strany 2 - PLASTIC SUPPLY LINE

7301270-100 Rev. A67INSTALL TOILETa. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange.

Strany 3 - ASSEMBLY

7301270-100 Rev. A9 10ADJUSTMENTS a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup.Se

Strany 4 - San Juan Capistrano, CA 92675

7301270-100 Rev. A12CADET® 3 TOILET FIVE YEAR LIMITED WARRANTYThis limited warranty applies only to the original purchaser and installation of the pro

Komentáře k této Příručce

Žádné komentáře

American Standard Compact Cadet 3 2568 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Zdravotnický sortiment American Standard Compact Cadet 3 2568. American Standard Compact Cadet 3 2568 User's Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Zdravotnický sortiment American Standard Compact Cadet 3 2568